How to configure your Philips 10BDL3051T or 10BDL4151T tablet for Pronestor display
This guide will show you how to configure a Philips 10BDL3051T or 10BDL4151T tablet for Pronestor display.
Table of contents
Requirements
A Pronestor Display solution, version 6.0.7 or newer
USB stick
Physical access to the Philips 10BDL3051T or 10BDL4151T tablet
Your Pronestor Display Url
Introducing your Philips tablet
Front:
Back:
Notice the highlighted buttons. Button 1 is the action button, button 2 is the volume control.
Check the firmware version
This is only relevant for 10BDL3051T. If you have a 10BDL4151T, please go to Factory reset - must ALWAYS be done
Pronestor Display only supports firmware version 3.05 for 10BDL3051T or newer
Press the action button and the volume control to access the settings area. You will be asked for a password. The default password is 1234
Click "Settings"
Click "About" and check the build number
If the build number is 3.05 or higher, go to the chapter Factory reset - must ALWAYS be done.
If the build number is 3.04 or lower you need to update the firmware to 3.05. Please contact your hardware supplier if you need further assistance with updating the firmware.
Factory reset - must ALWAYS be done
A factory reset is essential. When you unbox the tablet, it hasn't had a factory reset. Most of the bugs we get are because the device hasn't had a factory reset. Save yourself a lot of trouble and get it done while you are setting it up.
Factory reset will delete all files on the device. So please remember to backup anything you need to save first.
To do a factory reset follow these steps:
Press the action button and the volume control to access the settings area. You will be asked for a password. The default password is 1234
Click "Settings"
Click "System Tools"
Click "Factory Reset"
Click "Factory Reset"
Your device will now reset and reboot. This will take a few minutes.
Installing the Pronestor Kiosk Browser
Download the latest kiosk browser here: Downloads
Copy it to a USB stick
Insert the USB into your Philips tablet
Press the action button and the volume control to access the settings area. You will be asked for a password. The default password is 1234
Click "Apps"
Click "File Manager"
Browse to where you put the file on the USB stick. Root is "mnt/usb_storage/"
Select the .apk file and press "Open"
Follow the install instructions
Configuring the Pronestor Kiosk Browser
How to set the Pronestor Kiosk browser as the startup app
Hit the back button until the file manager is closed, or press the action button and the volume control to access the settings area. You will be asked for a password. The default password is 1234
Click "Settings"
Go to Sound
Turn the volume all the way down
Go back to the settings menu
Click "Signage Display"
Scroll down until you see "Custom App"
Click "Custom App"
Click "Select App"
Click "KIOSK"
Click "Save"
Hit the back button until you're back to start, or press the action button and the volume control to access the settings area. You will be asked for a password. The default password is 1234
Click "Settings"
Click "Signage Display"
Click "Boot on source"
Click "Input"
Click "Custom App"
How to remove the bottom navigation bar
Press the action button and the volume control to access the settings area. You will be asked for a password. The default password is 1234
Click "Settings"
Click "System Tools"
Under "Navigation bar" click the circle at "Disable"
How to configure the Pronestor Kioskbrowser to point towards your Pronestor Display
Press the action button and the volume control to access the settings area. You will be asked for a password. The default password is 1234
Click "Apps"
Click "KIOSK"
Click and hold at the lower right corner for about 4 seconds. You will know that you got the right point when you see a gray square. You will be asked for a password. The default password is 1234
Click "URL"
Insert your Pronestor Display URL for this tablets’ room and click "OK"
In this example it's https://pronestor.pronestordisplay.com but check that the link is for your site
Click "Go to url"
Click "ok" to the reminder
Click on the meeting room this Display should show
Your Pronestor Display is now ready for use.
Setting up TeamViewer for Centralized Device Management
Prerequisites: Firmware version FB02.05 (or newer), TeamViewer 12 (or newer)
The FB02.05 firmware version for Philips 10BDL3051T comes with a TeamViewer Host application. This can be used for setting up centralized device management.
Please note that the following is merely a suggestion on how it can be implemented - Pronestor does not provide support in third-party software. Please refer to your hardware provider for a setup guide.
On the device, open the "Host" application from the home screen
In the "Assign" tab, input credentials for a TeamViewer account with an active license and click "Assign"
An email will be sent to the email address related to the TeamViewer account with verification details
Once verified, the device will be available for remote control from the TeamViewer account